Magnetic Type Pipeline Orbital Pipe Welding Machine Sells Well in Southeast Asia

WQ-III Magnetic Pipe Orbital Welding Tractor with Electric and Manual Type   Product Description    WQ-III is suitable for welding internal and external walls of pipelines. No rails are required and welding can be carried out along the arc surface of the workpiece.    CO2 automatic welding tractor is widely used in ships, bridges, locomotives, steel structure, petrochemical industry and other industries, suitable for a variety of welding structures, such as: reinforcement plate, rib plate, cross parts of the welding, box beam welding, etc.. Its main advantages are:1, Reduce labor intensity and improve working environment;  2, To improve the working efficiency, it is 1.5 times of manual welding;  3, Avoid the poor quality of welding seam caused by human factors, the defect rate of manual welding is about 20%, and the automatic welding tractor will not produce welding defect rate because of artificial welding. Therefore, its comprehensive benefit is nearly 200% higher than that of manual welding;  4, High degree of automation to ensure the stability of welding quality; 5, Simple and convenient operation, do not need very skilled technical workers.  Product Features1, WQ-III is swing automatic welding device, one welding can get a wider weld.2, Swing speed, swing range, center position and left and right residence time can be adjusted, suitable for various specifications of the weld.3, Small size, light weight, easy to install and move, unskilled workers can also carry out welding.4, Permanent magnet is installed to avoid welding line disconnection during welding. Application EnvironmentSuitable for pipe welding of various steel structures.Major ComponentComponents: welding gun swing device, slider, welding gun handle, control box, control panel and other accessories:1, Swing device: used to drive the welding gun for pendulum swing welding  2. Driving part: the driving device of the trolley is composed of four magnetic wheels, helical gears, chains and sprockets  3, Slider part: used to adjust the position of the welding gun, you can fine-tune the position before and after when welding. 4, welding gun fixture: welding gun clamping device, it can adjust the Angle of the welding gun.  5, control box: All movements of the tractor can be adjusted. For details, refer to the operation method of the control panel  Control Panel Introduction1, Knob for adjusting current and voltage: Turn the knob clockwise to increase the value (The tractor has two power plugs of 3P and 8P, when using 3P plug, the current and voltage adjustment knob is invalid, and then the current and voltage of the wire feeder must be adjusted; Current and voltage control knob is effective when using 8P plug)2, Selection knob for welding/non-welding: the knob must be in the welding position to weld3, Point feed: manual wire feed device4, Walking switch: control the car walking and stopping, if the "welding/non-welding" switch is placed in the "non-welding" position, open the walking switch, the tractor only walking without welding5, Walking speed adjustment: the adjusting knob of tractor walking speed. It is recommended to adjust the tractor walking speed after turning on the walking switch6, Choice of walking direction: choose to walk left or right7, Power switch and indicator light: the indicator light is on after the power is energized8, Swing control part: it can adjust swing speed, swing range, left and right stay time, center position and swing modeProduct ParametersItemsParameterNoteTractorPower supplyAC 220VSize240×330×310W×L×HWeight16KgIncluding swingerMoving modeFour-wheel drive Magnet-wheel Walking speed0∼700mm/minSwing motorDC24V 18RPMAdjustable range of welding gunUp and downBefore and after85mmOperating Angle adjustment range360°Carry out Angle adjustment range0°ControlOperating functionSwing mode           Swing speed0-10RPM(Show with scale)Swing scope0-±10°(Show with scale)Left and right residence time adjustment0-2S(Show with scale)Central range of movement0-±8°Inching wire feedingWalking starts/stopsWelding current/voltage controlChoice of walking directionWalking speed regulation0∼1000mm/min(Show with scale)Welding/non-welding options Product InstallationA. Preparation for welding1, The necessary tools for welding are welding machines and wire feeding devices2, Special control cables (AC 220V) are required. Different welding power supplies require different cables3, CO2 tanks for welding are required4, CO2 automatic welding torch5, Other necessary tools B. Tractor connection method1, Install the tractor and place the tractor on the working surface2, Install the wire on the wire feed tray and pull the wire to the end of the torch3, The end of the torch is connected to the wire feeder4, The control power supply is connected to the 8P port of the control panel of the tractor5, Control power cable is connected to AC 2206, The special control cable has four joints, one is connected to 220V power supply, the other is connected to weldin